Electrical problem at home? Talk to a licensed Newnan electrician.
Free estimates · GA License EN216120 · Mon–Fri 8–5
You put in a brand-new bulb, flip the switch, and nothing happens. It is one of the most common calls we get from homeowners in Newnan and Coweta County, and the good news is that the cause is usually simple to find. Sometimes it is the bulb or the switch, and sometimes it is a loose connection or a worn-out fixture that needs a licensed electrician. Here is what usually causes it, the warning signs to call about, and when it is time to call.
Warning Signs to Call About
When a fixture stays dark after a new bulb, the cause can be the bulb type, a dimmer, a switch, a tripped breaker, a GFCI or a wiring problem, and the right fix depends on which one it is. Call a licensed electrician if:
- A new bulb still does not light the fixture
- LED bulbs flicker or fail on an older dimmer or in an enclosed fixture
- Other lights or outlets in the room are dead too
- A breaker keeps tripping, or a GFCI will not stay reset
- The light works only some of the time
Hallways, stairs, and big rooms often have three-way switches, and bathroom, garage, porch, and basement lights are sometimes wired through a GFCI outlet, which makes the cause harder to see. If a GFCI will not reset, our page on a GFCI outlet not resetting in Newnan explains what that usually means. A breaker that keeps tripping is a problem a licensed electrician should check and fix. See our guide to a breaker that keeps tripping.
Common Reasons a Light Fixture Stops Working
- A worn-out switch. Switches wear out after years of use. A switch that feels loose, clicks without doing anything, or works only sometimes is a common culprit.
- A failed dimmer. Older dimmers often fail after LED bulbs go in, or they hum, buzz, and flicker before they quit.
- A loose wire connection. A connection can loosen at the switch, the fixture, or another device on the same circuit. Lights that work only when you tap the fixture or wiggle the switch point to this.
- A worn socket. The small brass tab in the socket can flatten over time so it no longer touches the bulb. Heat from old incandescent bulbs makes this worse.
- A failed LED fixture or driver. Many newer fixtures have built-in LEDs with no bulb to change. When the LED module or driver fails, the fixture usually needs replacing.
- A problem with the circuit. If other lights or outlets nearby are dead too, the issue may be upstream, not in the fixture.
For switch problems, see our page on a light switch not working in Newnan, GA. If your lights are flickering instead of dead, our guide to lights flickering in Newnan homes covers the usual causes. And if a whole room went dark at once, read about power out in one room.
Urgent Warning Signs to Call About
- A burning smell, scorch marks, or a discolored switch plate or fixture base
- A switch or dimmer that feels warm or hot to the touch
- Buzzing, crackling, or sizzling from the fixture or switch
- Lights that dim or flicker when an appliance turns on
- Several lights or outlets out at the same time with no tripped breaker
- A fixture that went out after water got into a bathroom, attic, or outdoor box
Any of these can mean a loose or overheating connection, which a licensed electrician should check before the circuit is used again. Learn more about a burning smell from an outlet or switch, or let our electrical troubleshooting and repairs team track down the cause.
Repair or Replace the Fixture?
If the switch, wiring, and circuit test fine, the fixture itself is usually the problem. A simple fixture with a worn socket can sometimes be repaired, but an older or integrated LED fixture is often worth replacing, especially if you have wanted a brighter or more efficient light anyway. Our lighting repair in Newnan service handles fixtures that have stopped working, and our lighting installation in Newnan, GA covers new fixtures, chandeliers, pendants, and under-cabinet lights.
Replacing a fixture is also a good time to upgrade the control. A modern LED-compatible dimmer stops flicker and buzz, and recessed LED lights can brighten a dim kitchen, hallway, or bonus room. See our dimmer switch installation and LED recessed lighting in Newnan pages for ideas.
Why You Should Not Guess Inside the Box
Opening a switch box or taking down a fixture is work for a licensed electrician. Older Newnan homes can have brittle wiring, shared neutrals, or connections from past do-it-yourself work that are easy to make worse. A licensed electrician can test the circuit, find the real cause, and fix it the right way the first time.
Serving Newnan and Nearby Communities
Shocking Electric Solutions, Inc. is a licensed electrical contractor based in Newnan, serving homeowners within about 40 miles, including Peachtree City, Tyrone, Sharpsburg, Senoia, Carrollton, and Riverdale. We offer free estimates, and our work is backed by a 2-year warranty. Learn more about our licensed electricians in Newnan, GA, our lighting installation in Peachtree City, and our electricians in Tyrone, Sharpsburg, Senoia, Carrollton, and Riverdale.
Call or Text Shocking Electric Solutions, Inc.
Light fixture still not working after a new bulb? Call Shocking Electric Solutions, Inc. at (678) 552-9399 or text (470) 516-7261. Many customers prefer texting, and since our main phone is VOIP and cannot receive texts, the text line is the easiest way to reach us and send a photo of the fixture or switch. Same-day and next-day appointments are often available. You can also email info@shockingelectricsolutions.com. We are located at 1002 Highway 16 W, Suite A, Newnan, GA 30263.
Related reading: Recessed Lighting Layout Tips for Newnan Homes
Watch: Too-Big Bulbs in an Old Light Fixture
Sparky Jr. explains how bulbs over a fixture's wattage rating can overheat the wiring.